Sand and Dust Test Chamber-Linpin Instruments

Product Features

Product application:
The sand and dust test chamber is suitable for conducting dust-proof and dust-resistance tests on various automotive components, including headlights, dashboards, electrical dust covers, steering systems, door locks, and more.
Chamber structure:
Cabinet exterior material: High-quality steel plate with plastic spraying treatment. Cabinet interior material: Imported SUS stainless steel polished plate.

The sand and dust test chamber is equipped with a transparent glass door for convenient observation of the test samples inside.

The bottom of the test chamber is fitted with high-quality, fixed PU casters.

The bottom of the test chamber has a device for replacing the dust.
Control system:
The sand and dust test chamber adopts an imported programmable controller to effectively ensure that the test runs according to the standard.

It is equipped with vacuum extraction devices and a power failure recording device that can record for up to ten years. “Schneider” brand actuating components are used.

The dust-blowing fan operates with automatic alternating time cycles.
The vibration and non-vibration periods are automatically alternated.
There is a vacuum pressure indicator that can be adjusted.

The programmable controller has four output points that can simultaneously execute four different time programs.
Each output point of the programmable controller has two time period controls (i.e., start time and stop time).

The programmable controller can individually or collectively control the time for the dust-blowing fan, dust vibration, and the total test duration. The maximum test time is 99 hours and 59 minutes. The air speed inside the chamber is adjustable (automatically regulated through a frequency converter).
Compliance with standards:
GB4208 GB/T2423.37-1989

Product Parameter

Model	Studio Size (DWH)mm	Dimension（DWH）mm
LRHS-512-PS	800×800×800	1300×1050×1750
LRHS-800-PS	800×1000×1000	1300×1250×1950
LRHS-1000-PS	1000×1000×1000	1600×1250×1980
LRHS-1500-PS	1000×1500×1000	1600×1750×1980

Time Setting Range	1～9999H adjustable
air velocity	Not more than 2m/s
Dust blowing method	Continuous and periodic dust blowing at any time setting
sand and dust concentration	2～4kg/m³
Test dust	Drying talcum powder, silicate cement, chimney ash, etc.
Vacuum pump flow control	60～600L/H
Dust dehumidification	Electrically heated heating and dehumidification
Vibration time	1S-99H adjustable
Dust blowing time	1S-99H adjustable
recurring cycle	Dust blowing time, stop time and total time can be set arbitrarily.
viewing window	395×395mm(Effective vision)
Outer case material	High quality A3 steel plate electrostatic spraying
Inner box material	Imported high-grade stainless steel SUS304
Temperature Controller	“Taiwan Weilun” 7.0-inch color touch instrumentation
standard configuration		1 layer of sample rack, 1 scraper, 100g of talcum powder
Optional accessories		Vacuum system: rotary vane vacuum pump (equipped with vacuum piping device)
security protection		Fan motor overheating, the overall equipment phase / reverse phase, leakage protection Test timing, overload and short-circuit protection, automatic shutdown after fault alarms
Supply Voltage		AC380V±10% 50Hz
Power		0.9kW/0.9kW/1.2kW/1.2kW
operating environment		5℃～＋28℃ ≤85% RH
Note: 1、Can be customized according to the specific requirements of the user non-standard sand and dust test chamber etc 2、This technical information, if any change without notice

Industry News

Let’s Take a Look at the Components of a High and Low Temperature Test Chamber

From the outside, a high and low temperature test chamber may appear to be just a large box. However, its internal structure is not as simple as it seems.

Brief Introduction: Temperature and Humidity Requirements for the Three Processes of a Sand and Dust Test Chamber

When conducting tests with a sand and dust test chamber, there are primarily three processes involved. Some clients may not be familiar with these processes during initial consultations. Today, we will introduce these three processes and their corresponding temperature and humidity requirements.

Rain test chambers are used to evaluate the waterproofing parameters and performance of automotive components, low-voltage electrical enclosures, and other products. These devices simulate relevant environmental conditions for testing.