Search for the product you are looking for
Fiberglass composite salt spray test chamber

Fiberglass composite salt spray test chamber

Product Introduction
Fiberglass composite salt spray test chamber for the assessment of the material and its protective layer of salt spray corrosion ability, as well as similar protective layer of process quality comparisons, and at the same time can be assessed for some of the products resistant to salt spray corrosion; used for parts and components, electronic components, the protective layer of metal materials, and industrial products of the composite salt spray corrosion test

Service Hotline

4000-662-888
Product Features
Product Parameter
Model Studio Size  (D*W*H)mm Dimension(D*W*H)mm
LRHS-108-RFHY 450×600×400 Subject to contractual three-view
LRHS-270-RFHY 600×900×500
LRHS-412-RFHY 750×1100×500
LRHS-663-RFHY 850×1300×600
LRHS-816-RFHY 850×1600×600
LRHS-1080-RFHY 900×2000×600
temperature range RT+5℃~80℃
Humidity range 30%~98% RH
Saturated drum temperature RT+10℃~70℃
Temperature uniformity ≤2℃
Temperature fluctuation ±0.5℃
Salt spray deposition 1~2ml/80 cm².h(16-hour average)
Compressed air pressure 2.00±0.01(kg/cm²)
Spraying method Continuous/periodic selectable
Specimen holder angle Can meet 15°, 30° tilt test
Test Methods NSS test AASS test CASS test
Case Material Fiberglass reinforced plastic (FRP)
Lid Material Fiberglass reinforced plastic (FRP)
Air-saturated drums High quality premium stainless steel SUS304
Pressurized Air Hose Material High quality rubber hose
Other pipelines Thickened Fluorosilicone Rubber Tubing
Temperature Controller High-quality “UEC” brand temperature and humidity meter
Dehumidification and cooling Single or double cascade refrigeration
Compressor Taikang, France
temperature sensor PT100 platinum resistance temperature measurement body
heater Titanium Heating Tube
interrupter Schneider miniature circuit breakers (to prevent short circuits in control circuits)
standard configuration V型样品架、圆棒、喷嘴、漏斗、计量筒、排雾管
security protection 整机欠相/逆相、设备定时、快速排雾指示、试验结束
超温、低水位保护、漏电、短路、 压缩机超压过载
Supply Voltage AC380V±10% 50Hz
Power 8.5kW/10.0kW/12.0kW/13.5kW/15.0kW/17.5kW
Temperature: 5℃~+35℃((Average temperature over 24 hours ≤ 28°C)
Relative Humidity: ≤85%RH
Note:
1、 the above data are in the use of ambient temperature of 25 ℃ and well ventilated conditions measured
2、Can be customized according to the user’s specific requirements, such as non-standard test chamber
3、This technical information, if there is any change without prior notice

 

Product Recommendation
Industry News
A high-temperature test chamber is an essential instrument for evaluating the reliability of industrial products under extreme heat conditions. It tests various performance metrics of products exposed to high and low-temperature transitions.
The ozone aging test chamber is an instrument used in the aging resistance testing process of some materials.
Rain test chamber is a test instrument to test whether the waterproof is good, the figure of this equipment can be said to be everywhere, applied in various places. Small to our usual use of cell phones, flashlights and other lighting apparatus; large to the aerospace industry, lighting systems, signaling device testing and so on. Waterproof has always been a lot of industry can not get around a topic, a lot of equipment once the rain and other wet, its service life will be greatly reduced, this equipment in the waterproof performance test link plays a vital role.