Choosing the Right Lamp for Your UV Aging Test Chamber

Source：LINPIN Time：2025-04-02 Category：Industry News

The lamps in a UV aging test chamber will degrade over prolonged use, and aging lamps need to be replaced promptly. So, how do you select the right lamp for the test chamber? Are there any tips for making the right choice? Today, we’ll share some useful tips for selecting UV aging test chamber lamps.

There are two types of lamps in a UV aging test chamber, and the choice depends on the characteristics of the test sample. Here are some features of the UVA-340 lamp:

The UVA-340 lamp emits short-wave UV light similar to that in sunlight, with a wavelength range from 365 nm down to the solar cutoff point of 295 nm.

UV aging test chamber
Features of the UVB-313 lamp:

The UVB-313 lamp emits short-wave UV light that is even stronger than the UV radiation typically reaching the Earth’s surface.
This type of lamp can significantly accelerate material aging but may also cause unrealistic damage to certain materials.
It is primarily used for quality control, R&D testing, and evaluations of highly weather-resistant materials.
Theoretically, the aging acceleration effect of the UVA-340 lamp is not as fast as that of the UVB-313 lamp. However, in terms of weather resistance testing, the UVA-340 lamp has a clear advantage over the UVB-313 lamp. So, which lamp should you choose for your UV aging test chamber? The decision ultimately depends on the customer’s specific testing requirements, such as test duration.

Once you’ve selected the appropriate lamp for your UV aging test chamber, it’s time to replace the old lamp. Here’s how to do it:

Remove the electrical compartment cover from the top rear of the chamber.
Take off the UV temperature sensor panel and other relevant panels.
Open the side doors of the chamber.
Disconnect the lamp connectors on both ends.
Slowly remove the lamp from the inside.
Note: New lamps may emit a spiral or flickering light initially, but this does not affect the lamp’s spectral output.

After removing the old lamp, install the new UV lamp using the same method. If the operator is unsure about the correct replacement procedure, a technician should handle the task. Once the new lamp is installed, the test chamber is ready for subsequent experiments.

Previous article: Why Can’t the Humidity Drop in a Temperature & Humidity Test Chamber?

Next article: Are You Using the Salt Spray Test Chamber Correctly?

News Recommendation

25.07

The Concept and Differences Between IPX56 Rain Test Chamber and IP44 Water Resistance

When discussing the water resistance of electronic products, we often encounter various water resistance standards. Among them, the IPX56 rain test chamber and IP44 water resistance are two common water resistance testing standards.

25.04

What Challenges Might Be Encountered During Rain Test Chamber Testing?

Rain test chambers, also commonly referred to as waterproof test chambers or box-type rain test chambers, are primarily used to evaluate whether the casings or sealed components of electrical and electronic products, household appliances, and various lighting fixtures are affected during rain testing, and whether their operational performance and adaptability can be maintained.

24.07

LINPIN Instruments in Action for Large-Scale Equipment Renewal

Recently, China issued the Action Program for Promoting Large-scale Equipment Renewal and Consumer Goods Trade-in (hereinafter referred to as the Action Program), which systematically deploys 20 specific measures around the implementation of the four major actions of equipment renewal, consumer goods trade-in, recycling, and standard enhancement. Since the release of the Action Program, provinces and municipalities have responded to the policy by gradually promoting the relevant work and formulating provincial and municipal plans to promote large-scale equipment renewal and consumer goods trade-in.

25.04

Reminder: Things You Should Never Do to the Compressor of a High and Low Temperature Test Chamber

The refrigeration compressor is one of the key components affecting the test results of a high and low temperature test chamber. To ensure smooth operation, proper maintenance of the compressor is essential. During daily operation, the following actions must be avoided

25.03

What Can a Salt Spray Test Chamber Be Used For?

Why do so many industries rely on salt spray test chambers? Because many manufactured products need to be tested for their resistance to salt spray corrosion. However, relying solely on natural atmospheric conditions for testing could take years or even decades.